The right access point today is chosen not by the maximum "speed on the box", but by a set of quite mundane parameters: how many bands are actually used, is there 6GHz, how many spatial streams does the radio frequency give, which uplink is on the wired side, is PoE supported, is there a second Ethernet port, can the device works as a bridge, whether it supports mesh, how exactly it can be controlled and in which case it is made. This is especially important for Zyxel, because the Wi‑ ...

The Zyxel IAP500BE is a Wi‑Fi 7 industrial access point that focuses not so much on a typical office scenario as on working in a technically complex environment where stability, fault tolerance, and predictable hardware behavior come to the fore. The Zyxel IAP500BE is a Wi-Fi 7 industrial access point that focuses not so much on a typical office scenario as on working in a technically complex environment where stability, fault tolerance, and predictable hardware behavior come to the fore. ...

The Zyxel CX4800-56F is a high-density L3 aggregation optical switch in which the company pioneered the use of 100G ports: 8 QSFP28 100GbE uplinks complement 48 SFP+/SFP28 slots with 10/25gbe support, forming a single 56-port stack for traffic aggregation in campus and data centers factories. With a pass-through switching matrix of up to 4 Tbit/s and forwarding speeds of up to 2 billion packets per second, this switch confidently closes scenarios of highly loaded highways, where not only ...

This is a Wi-Fi 7 model with a simplified radio part with a 2x2:2 antenna formula and a channel width of up to 240 MHz, which gives an overall air speed of up to 5.1 Gbit/s. With a 2.5-gigabit network port, the access point can easily handle such complex tasks as backup of client laptops, synchronization of media archives, streaming video in any resolution, and in general, everything that requires the transmission of large amounts of data "over the air" is not very demanding of delays ...

... authentication. Using a wireless controller allows you to automatically adjust ... necessary that the Wi-Fi controller be on the same ... and cloud service, as Zyxel did with Nebula Control Center ... Center Since the Wi-Fi controller takes over the lion' ... the first route first and make the transfer between the ... , we used the  Zyxel NWA210BE  and  Zyxel WBE530  access points connected ... 7, switching is not exactly much slower. If the client ... , and importantly, this The network status is configured in just 2 ...

The NWA210BE model is a model of the Wi-Fi 7 standard in the medium price range, it has 2 radio modules with formulas 2x2:2 for 2.4GHz and 4x4:4 for 5 and 6 GHz. The 5 and 6 Hz ranges are controlled by a single BandFlex radio module, so only one of them can operate at a time. The NWA210BE supports a channel width of 320 MHz, which allows for high point-to-point speeds, which may be in demand when building wireless bridges or connecting high-resolution NVR cameras. The new Wi-Fi 7 standard ...

Following the recommendations of "best practice", network devices of various purposes, such as IoT, work computers, smartphones, guest devices, should always be located in different subnets, and ideally terminated through a common security gateway, however, in some cases, for example, when the gateway does not cope with the flow of traffic, distribution by subnets it can be assigned to a network switch to separate different devices by VLANs, thus separating access to different networks ...

... the Zyxel USG Flex 100AX to Wi-Fi controller mode ... to control Zyxel access points, and ... switching to Wi-Fi controller mode immediately disables the ... I recommend using the Zyxel Nebula cloud controller for wireless networks ( ...  from the global Internet). Zyxel has a very interesting Secure ... of the Zyxel USG Flex100AX, so there is not much to ... control the rest of the network stack directly, including monitoring using ... when the wireless access point controller is turned on, the ...

We have a rather interesting class of L3 switches in front of us: multi-gigabit PoE models with a relatively small number of ports, an average PoE budget by modern standards, but 10-gigabit uplinks. They are interesting because the manufacturer has placed 2.5G PoE + 10G in a compact 9-inch rack housing with a silent fan, and such a switch can be installed at home, in a 1-room office, under a false ceiling or in narrow telecommunication cabinets. We have a rather interesting class of L3 ...

We will take two switches: the Taiwanese brand Zyxel and the Chinese counterpart from a little-known manufacturer and look at the design differences and what they affect in order to answer the question - does it make sense to overpay for design features? It's no secret that almost all modern electronics are manufactured in China, even if they are developed in the USA, Europe, Japan or Taiwan – the Chinese have not only learned how to do things efficiently, but have also grown such IT giants ...